So, as you could have guessed, I am a jewelery fanatic! Accessories are a girl’s best friend, considering I cannot afford diamonds. I found this lovely project idea for a jewelry storage on DesignSponge. It’s an incredible idea and doesn’t seem too difficult or expensive to recreate. The hardest part would most likely be finding the perfect silouhette, the rest seems like a breeze and the end result is well, just look for yourself! Here’s a quick step to step guide, so you too can have a beautiful place to show off your flashy accessories!
materials (for both versions):
1. piece of wood at least .5″ thick and 12″ x 17″ (i used an ikea wood shelf that was 14″ wide x 36″)
2. jigsaw (with a fine tooth blade for detail cuts)
3. safety goggles and dust mask
4. sandpaper
5. white paint
6. paintbrush
7. table clamps (for securing the wood during cutting. you should have two of these)
8. pencil
for tabletop version:
1. 9″ x 12″ wood plaque (these are available at craft stores)
2. 3/4 inch screws (x4)
3. 4″ metal “L” bracket (usually comes in pairs at the hardware store)
4. two pairs of pliers
for wall mount version:
1. scrap piece of wood (around 2″ thick and small enough to fit behind bust)
2. 2″ screws (x2)
3. cup hooks (x2)
4. nails or screws (for the wall) (x2)
cost:
wood shelf $5
wood plaque $2
paint, tools: free (on hand)
bracket: $2
time:
3 hours (including drying time)
Instructions.
1. print out a bust template at 140% the original size (or print and copy at 140%). the final dimensions of the bust should be about 11″ at its widest point and 17″ tall.
2. cut out the template and trace onto your piece of wood with a pencil.
3. clamp down the wood and use your jigsaw to cut out the shape. the key to using the jigsaw for small detailed shapes is cutting in pieces. do not try to cut one long outline of the template. cut away at the shape in small sections, coming at the edges from all different angles to get the best, cleanest cut around the shape. this means you will be cutting out little chunks of wood around the lips and nose, but just work slowly and carefully and you’ll get good clean detail. you will have to stop a couple times to adjust the cutout and re-clamp for better cutting angles.
4. once the shape is cut out, use the sandpaper to smooth the edges and remove any loose splinters.
5. wipe the shape clean of any sawdust and lay on a painting surface.
6. paint the shape and the base white. allow to dry.
(note: the earrings are hung from a thumbtack pushed into the wood)
for tabletop version:
1. while pieces are drying, use the pliers to slightly bend the “L” bracket edges towards each other, to create an angle slightly smaller than 90 degrees. this allows your bust to tilt back slightly when attached.
2. once pieces are dry, screw the “L” bracket into the back of the bust with the bottom of the bracket flush with the bottom of the bust. then screw the bracket into the plaque near the back of the length of the plaque.
3. paint the bracket white. let dry.
for the wall mount version:
1. use the 2″ screws to secure the thick scrap of wood to the backside of the bust, centered in the chest area a few inches down from the neck.
2. screw the cup hooks in on the right and left corners of the outermost edge top of the scrap piece of wood (farthest from from the bust).
3. paint the whole attachment white, and let it dry. it is now ready to hang by two nails or screws in a wall.
And now its time to enjoy your work! You’re Done!
To get a more extensive look at this this project and many more amazing ones,
check out more at Design Sponge.
I already gathered some supplies! I cannot wait to get started on my own!
I’ll post pictures up when I do!
I absolutely adore this, there are many more colors available too. I think this would look lovely
katherinemack 